Fully hydraulic guillotines. The patented direct-hydraulic drive concept sets new standards for the performance of cutting machines.
- Intuitive control with 15“ TFT-display (PCC)
- Solid cast iron frame
- Rust-proof cutting table with air film
- Program correction function (linear and percentage)
- Optical cut indicator
- Automated knife change at the front
|MODEL ||115H ||137H ||155H |
|Max. cutting width (mm) ||1150 ||1370 ||1550 |
|Max. cutting length (mm) ||1150 ||1370 ||1550 |
|Max. cutting depth (mm) ||170 ||170 ||170 |
|Smallest cut* |
|100/40 ||100/40 ||100/40 |
|Air film ||yes ||yes ||yes |
|Display ||15" TFT |
|15" TFT |
|15" TFT |
|Programs (qty) ||Unlimited ||Unlimited ||Unlimited |
|Working height (mm) ||900 ||900 ||900 |
|Net weight (kg) ||2750 ||3350 ||3650 |
|Power ||8000W ||8000W ||8000W |
|Dimensions WxDxH (cm) ||202 x 229 x 162 ||224 x 277 x 162 ||242 x 325 x 162 |
|Warranty (yrs) ||1 ||1 ||1 |
|Side tables ||LST 750 (750 x 750 mm) (pic. 1-3) |
LST 1000 (1000 x 1000 mm)
|Swinging and/or tilting back gauge, program-controlled ||The swinging back gauge is used for corrections when the print does not run parallel to the edge, or when parallel and non-parallel cuts are needed in the same cutting programme. The tilting back gauge corrects distortions created by pressure, as well as undercuts or overcuts which cannot be compensated for by adjusting the clamp pressure. |
|Downholder at the back gauge, program-controlled ||The optional downholder avoids cutting inaccuracies resulting from shifting. During cutting, |
the material is subjected to additional holding by the downholder unit.
|Retractable side gauge (ASL) ||The ASL unit is needed for automatic loading of the rear table. Once lowered into place, it |
can be used for automatic loading and raised upwards for lateral material alignment.
|Lay edge control, program-controlled ||The program-controlled unit makes it possible to position materials according to their print |
marks and align them to the side gauge of the guillotine. This option is especially important
for cutting concave or convex piles without straight alignment edges. This feature is not available in connection with the downholder.
|TrimmMaster (automatic waste removal) ||The horizontal extendable front table (featuring a cast iron underframe with a 2mm VA steel surface) makes it possible to remove waste automatically with the TrimmMaster unit. There |
is a shaft between the table and the cutting stick which opens pneumatically over the entire cutting width. Waste drops down through the shaft along a metal guide into a bin or onto a waste conveying system for disposal. The TrimmMaster unit is a highly efficient and productive option for automatically removing cutting waste and is especially recommended for intermediate cuts.
|Knives ||TCT |
|Retractable rear table cover ||The standard closed rear table cover is also available in a retractable version. This ensures that knives can be accessed from the back and the rear table can be cleaned properly. |
|Isoloc vibration absorber ||With difficult floors, it is recommended that Isoloc noise insulation is used. This entails placing |
the machine on four vibration absorbers resulting in a higher working height of up to 95 cm. The anti-vibration package includes levelling discs and levelling bolts to absorb cutting movements. The effective vibration insulation also helps reduce noise and is especially recommended for
machines installed above ground level.
|Narrower clamp cover plate ||This special clamp cover plate comes in a narrow version to replace the existing plate and allows for small cutting sizes - naturally, without any loss of quality. The unit can be mounted from the |
operator side. This plate reduces the smallest cut from 100 mm (with standard clamp cover palte)
to 60 mm.
|Waste bin ||This solid plastic container comes on rollers to provide plenty of room for cutting waste, improving efficiency by making it easier to throw away rejects next to the side table. |
For more information, see attachments below.